F FITS keywords

 F.1 Demodulated data
 F.2 Rebinned data

FITS information is stored in the NDF FITS extension of all SCUBA NDFs. This information can be accessed by using the Kappa fitslist command (or, less conveniently, with hdstrace). This appendix gives a full listing of all the information stored in the FITS header.

F.1 Demodulated data

All observation parameters are stored in the NDF FITS extension. They can be accessed using the Kappa task fitslist. The same information is stored in the reduced files but in the HEADER component.

  % fitslist apr8_dem_0059
  ACCEPT  = ’not used’           / accept update; PROMPT, YES or NO
  ALIGN_AX= ’not used’           / Alignment measurements in X or Y axis
  ALIGN_SH=                   -1 / Distance between successive alignment offsets(
  ALT-OBS =                 4092 / Height of observatory above sea level (metres)
  AMEND   =             1.117139 / Airmass at end of observation
  AMSTART =             1.123245 / Airmass at start of observation
  APEND   =             625.0427 / Air pressure at end of observation (mbar)
  APSTART =             624.7985 / Air pressure at start of observation (mbar)
  ATEND   =             0.158733 / Air temp. at end of observation (C)
  ATSTART =             0.305252 / Air temp. at start of observation (C)
  BOLOMS  = ’SHORT,LONG’         / Names of bolometers measured
  CALIBRTR=                    T / Internal calibrator is on or off
  CAL_FRQ =                1.984 / Calibrator frequency (Hz)
  CENT_CRD= ’RB      ’           / Centre coordinate system
  CHOP_CRD= ’AZ      ’           / Chopper coordinate system
  CHOP_FRQ=              6.94444 / Chopper frequency (Hz)
  CHOP_FUN= ’SCUBAWAVE’          / Chopper waveform
  CHOP_PA =                   90 / Chopper P.A., 0 = in lat, 90 = in long
  CHOP_THR=                   60 / Chopper throw (arcsec)
  DATA_DIR= ’apr8    ’           / Sub-directory where datafile was stored
  DATA_KPT= ’DEMOD + RESAMPLED’  / The type of data stored to disk
  END_AZD =              165.715 / Azimuth at end of observation (deg)
  END_EL  =                   -1 / Elevation of last SKYDIP point (deg)
  END_ELD =              63.6382 / Elevation at end of observation
  EQUINOX =                 2000 / Equinox of mean coordinate system
  EXPOSED =             3.022848 / Exposure per pixel (seconds)
  EXP_NO  =                    4 / Exposure number at end of observation
  EXP_TIME=             1.007616 / Exposure time for each basic measurement (sec)
  E_PER_I =                    4 / Number of exposures per integration
  FILTER  = ’450N:850N’          / Filters used
  FOCUS_SH=                   -1 / Shift between focus measurements (mm)
  GAIN    =                   10 / Programmable gain
  HSTEND  = ’23:43:50.003365’    / HST at end of observation
  HSTSTART= ’23:35:09.999847’    / HST at start of observation
  HUMEND  =                   22 / Humidity (%) at end of observation
  HUMSTART=                   23 / Humidity (%) at start of observation
  INSTRUME= ’SCUBA   ’           / Name of instrument used
  INT_NO  =                    3 / Integration number at end of observation
  JIGL_CNT=                   64 / Number of offsets in jiggle pattern
  JIGL_NAM= ’JCMTDATA_DIR:tile_64_3p09.JIG’ / File containing jiggle offsets
  J_PER_S =                   16 / Number of jiggles per switch position
  J_REPEAT=                    1 / No. jiggle pattern repeats in a switch
  LAT     = ’-005:31:08.40’      / Object latitude
  LAT-OBS =        19.8258323669 / Latitude of observatory (degrees)
  LAT2    = ’not used’           / Object latitude at MJD2
  LOCL_CRD= ’RB      ’           / Local offset coordinate system
  LONG    = ’+012:53:35.84’      / Object longitude
  LONG-OBS=        204.520278931 / East longitude of observatory (degrees)
  LONG2   = ’not used’           / Object Longitude at MJD2
  MAP_HGHT=                  180 / Height of rectangle to be mapped (arcsec)
  MAP_PA  =                    0 / P.A. of map vertical, +ve towards +ve long
  MAP_WDTH=                  180 / Width of rectangle to be mapped (arcsec)
  MAP_X   =                    0 / Map X offset from telescope centre (arcsec)
  MAP_Y   =                    0 / Map Y offset from telescope centre (arcsec)
  MAX_EL  =                   -1 / Max elevation of sky-dip (deg)
  MEANDEC =            -5.790909 / -5:47:27.27173 = approx. mean Dec. (deg)
  MEANRA  =             194.0517 / 194:03:06.053467 = approx. mean R.A. (deg)
  MEAS_NO =                    1 / Measurement number at end of observation
  MIN_EL  =                   -1 / Min elevation of sky-dip (deg)
  MJD1    =                   -1 / Modified Julian day planet at RA,DEC
  MJD2    =                   -1 / Modified Julian day planet at RA2,DEC2
  MODE    = ’MAP     ’           / The type of observation
  N_INT   =                    3 / No. integrations in the observation
  N_MEASUR=                    1 / No. measurements in the observation
  OBJECT  = ’3c279   ’           / Name of object
  OBJ_TYPE= ’PLANET  ’           / Type of object
  OBSDEF  = ’3c279_map.obs’      / The observation definition file
  OBSERVER= ’Captain Nemo’       / The name of the observer
  PROJ_ID = ’scuba   ’           / The project identification
  RUN     =                   59 / Run number of observation
  SAM_CRDS= ’NA      ’           / Coordinatesystem of sampling mesh
  SAM_DX  =                   -1 / Sample spacing along scan direction (arcsec)
  SAM_DY  =                   -1 / Sample spacing perp. to scan (arcsec)
  SAM_MODE= ’JIGGLE  ’           / Sampling method
  SAM_PA  =                   -1 / Scan P.A. rel. to lat. line; 0=lat, 90=long
  SPK_NSIG=                    0 / N sigmas from fit of spike threshold
  SPK_RMVL=                    T / Automatic spike removal
  SPK_WDTH=                    0 / Assumed width of spike
  START_EL=                   -1 / Elevation of first SKYDIP point (deg)
  STATE   = ’Terminating         :   RECORD_DATA RESET_DATA_SIZE RECORD_DATA’ /SC
  STEND   = ’12:28:40.78857’     / ST at end of observation
  STRT_AZD=              161.247 / Azimuth at observation start (deg)
  STRT_ELD=               63.081 / Elevation at observation start (deg)
  STSTART = ’12:19:59.36714’     / ST at start of observation
  SWTCH_MD= ’BMSW    ’           / Switch mode of observation
  SWTCH_NO=                    1 / Switch number at end of observation
  S_PER_E =                    2 / Number of switch positions per exposure
  TELESCOP= ’JCMT    ’           / Name of telescope
  TEL_OPER= ’Ned Land’           / Telescope operator
  UTDATE  = ’1997:4:8’           / UT date of observation
  UTEND   = ’9:43:49.99992’      / UT at end of observation
  UTSTART = ’9:35:09.999847’     / UT at start of observation
  VERSION =                    0 / SCUCD version
  ALIGN_DX=            -0.414241 / SMU tables X axis alignment offset
  ALIGN_DY=             0.556058 / SMU tables Y axis alignment offset
  ALIGN_X =              -4.0787 / SMU tables X axis
  ALIGN_Y =              4.16459 / SMU tables Y axis
  AZ_ERR  =                    0 / Error in the telescope azimuth
  CHOPPING=                    T / SMU Chopper chopping state
  EL_ERR  =                    0 / Error in the telescope elevation
  FOCUS_DZ=            -0.113297 / SMU tables Z axis focus offset
  FOCUS_Z =                  -16 / SMU tables Z axis
  SEEING  =                0.316 / SAO atmospheric seeing
  SEE_DATE= ’9704072245’         / Date and time of SAO seeing
  TAU_225 =                0.096 / CSO tau
  TAU_DATE= ’9704080210’         / Date and time of CSO tau
  TAU_RMS =              3.0E-03 / CSO tau rms
  UAZ     =              3.35413 / User azimuth pointing offset
  UEL     =              2.04832 / User elevation pointing offset
  UT_DATE = ’ 8 Apr 1997’        / UT date at start of observation
  BAD_LIM =                   32 / No. spikes before quality set bad
  CALIB_LG=                    5 / Lag of internal calibrator in samples
  CALIB_PD=             64.02849 / Period of internal calibrator in samples
  CHOP_LG =                    4 / Chop lag in samples
  CHOP_PD =              18.2927 / Chop period in samples
  CNTR_DU3=                    0 / Nasmyth dU3 coord of instrument centre
  CNTR_DU4=                    0 / Nasmyth dU4 coord of instrument centre
  FILT_1  = ’450     ’           / Filter name
  FILT_2  = ’850     ’           / Filter name
  FILT_3  = ’not used’           / Filter name
  FILT_4  = ’not used’           / Filter name
  FILT_5  = ’not used’           / Filter name
  FLAT    = ’noiseflat.dat’      / Name of flat-field file
  JIG_DSCD=                   -1 / No. samples discarded after jiggle movement
  L_GD_BOL= ’H7      ’           / Bol. to whose value LW guard ring is set
  L_GUARD =                    F / Long wave guard ring on or off
  MEAS_BOL= ’not used’           / Bolometers  actually measured in observation
  N_BOLS  =                  128 / Number of bolometers selected
  N_SUBS  =                    2 / Number of sub-instruments used
  PRE_DSCD=                    0 / No. of samples discarded before chop movement
  PST_DSCD=                    0 / No. samples discarded after chop movement
  REBIN   = ’LINEAR  ’           / Rebinning method used by SCUIP
  REF_ADC =                   -1 / A/D card of FLATFIELD reference bolometer
  REF_CHAN=                   -1 / Channel of FLATFIELD reference bolometer
  SAM_TIME=                  123 / A/D sample period in ticks (64musec)
  SIMULATE=                    F / True if data is simulated
  SKY     = ’skydip_startup.dat’ / Name of sky opacities file
  SUB_1   = ’SHORT   ’           / SCUBA instrument being used
  SUB_2   = ’LONG    ’           / SCUBA instrument being used
  SUB_3   = ’not used’           / SCUBA instrument being used
  SUB_4   = ’not used’           / SCUBA instrument being used
  SUB_5   = ’not used’           / SCUBA instrument being used
  S_GD_BOL= ’D9      ’           / Bol. to whose value SW guard ring is set
  S_GUARD =                    F / Short wave guard ring on or off
  TAUZ_1  =                    0 / Zenith sky optical depth
  TAUZ_2  =                    0 / Zenith sky optical depth
  TAUZ_3  =                    0 / Zenith sky optical depth
  TAUZ_4  =                    0 / Zenith sky optical depth
  TAUZ_5  =                    0 / Zenith sky optical depth
  T_AMB   =                   -1 / The ambient air temperature (K)
  T_COLD_1=                   -1 / Effective temperature of cold load (K)
  T_COLD_2=                   -1 / Effective temperature of cold load (K)
  T_COLD_3=                   -1 / Effective temperature of cold load (K)
  T_COLD_4=                   -1 / Effective temperature of cold load (K)
  T_COLD_5=                   -1 / Effective temperature of cold load (K)
  T_HOT   =                   -1 / The temperature of the hot load (K)
  T_TEL   =                   -1 / The temperature of the telescope
  USE_CAL =                    F / .TRUE. if dividing chop by cal before rebin
  WAVE_1  =                  442 / Wavelength of map (microns)
  WAVE_2  =                  862 / Wavelength of map (microns)
  WAVE_3  =                    0 / Wavelength of map (microns)
  WAVE_4  =                    0 / Wavelength of map (microns)
  WAVE_5  =                    0 / Wavelength of map (microns)
  END

F.2 Rebinned data

The rebinned data files contain the following. Note that the astrometry information is not stored in the FITS extension.

  % fitslist n59_reb_lon
  OBJECT  = ’3c279   ’           / name of object
  FILE_1  = ’n59_sky_lon’        / name of input datafile
  SYSTEM  = ’EQUATORIAL(2000.0)’ / sky coordinate system
  LONG    =      3.3867510541917 / centre longitude (radians)
  LAT     =    -0.10104535223053 / centre latitude (radians)
  TELESCOP= ’JCMT-Hawaii’        / name of telescope
  INSTRUME= ’SCUBA   ’           / name of instrument
  WAVELEN =             0.000862 / Wavelength of the observation (metres)
  FREQ    =      347787074245.94 / Frequency of observation (Hz)
  FILTER  = ’450     ’           / Filter name
  SCUPROJ = ’RJ      ’           / SCUBA output coordinate system
  SCUPIXSZ=                    1 / Pixel size (arcsec)
  DATE-OBS= ’08/04/97’           / Date of first observation
  DATE    = ’2000-07-06T02:35:49’/ file creation date (YYYY-MM-DDThh:mm:ss UTC)
  ORIGIN  = ’SCUBA User Reduction Facility (SURF)’/  Origin of the FITS file
  OBSRA   =      194.04654166665 / RA of map centre (degrees; deprecated)
  OBSDEC  =     -5.7894722222218 / Dec. of map centre (degrees; deprecated)